Whirlpool Washer Error Codes: What They Mean and How to Fix Them

Your Whirlpool washer stops, beeps and shows a code like F9E1 or LF instead of the time left. The code is the washer telling you which part of the drain, fill, lock or motor system it is having trouble with. Many codes clear with a simple check of the drain hose, filter, door or water valves. Others point to a failed pump, lock or board. Here is what the common codes mean and what to do next.

Call Now – (650) 459-7977
  • Open 24/7
  • Fast response
  • Upfront quotes
  • All major brands
Technician shining a flashlight on a white washing machine control panel to read a blinking error code in a Mountain View laundry room

What does a Whirlpool washer error code mean?

A Whirlpool washer error code is a message from the control board about a system it cannot finish, such as filling, draining, locking the door or spinning the drum. Newer models show an F code plus an E code, like F9E1, where F is the system and E is the exact fault. Older and top-load models often show short codes like LF, Sd or dL.

Codes usually appear on the time display with a beep, and the cycle pauses. Some models only show a code when you press and hold a button combination. Others flash lights instead of letters. Write the code down before you clear it, because it is the best clue a technician has.

What do the 12 most common Whirlpool washer codes mean?

The codes we see most in Mountain View laundry rooms are drain codes (F9E1, F21), fill codes (LF, F8E1), lock codes (F5E1, F5E2, F5E3, dL), suds (Sd), motor and drive codes (F7E1, F3E1) and unbalanced load messages. Most of the drain, fill and suds codes have a simple first check you can do safely.

CodeWhat it usually meansTry first
F9E1, F21Long drain, water not leaving fast enoughClean the drain pump filter, check the hose
LF, F8E1Long fill, not enough water coming inOpen both faucets fully, check the hoses
F8E3Overflow, too much water detectedTurn off the faucets and call
F5E1, F5E2Door or lid switch or lock not closingClose the door firmly, clear the latch
F5E3, dLDoor or lid will not unlockWait 2 minutes, run Drain and Spin
Sd, SUdSToo many suds slowing the cycleUse HE detergent, less of it
F7E1Motor speed or drive problemReset power, then call
F3E1Pressure sensor problemCheck the small sensor hose, reset
F6E1 to F6E3Boards not communicatingReset power for 1 minute
F0E5Load too large or off balanceRedistribute the load, wash fewer items
F1E1, F1E2Main control board faultReset once, then call
uL or "unbalanced"Load bunched to one sideSpread items out, check leveling

Codes can differ slightly between Cabrio, Duet, front load and top load models, so check the tech sheet tucked inside the console or behind the lower panel for your exact model. Maytag and some Kenmore washers built by Whirlpool use many of the same codes.

How do you fix a long drain code like F9E1?

Start with the drain path. On a front loader, open the small door at the bottom front, drain the water into a shallow pan and clean the pump filter. Then make sure the drain hose is not kinked behind the washer and is not pushed too far into the standpipe. Run Drain and Spin. If the pump hums but no water moves, the pump is likely bad.

  1. Lay towels down and put a shallow pan under the filter door.
  2. Pull the small drain tube or slowly unscrew the filter to let water out.
  3. Remove coins, hair ties, socks and lint from the filter.
  4. Check the drain hose for kinks where the washer was pushed back.
  5. Make sure the hose goes no more than about 6 to 8 inches into the standpipe.
  6. Run a Drain and Spin cycle and listen to the pump.

Top-load Whirlpool washers do not have a user filter, so a long drain code there usually means a clog in the pump or hose, or a failed pump.

How do you fix a long fill code like LF or F8E1?

A long fill code means the washer did not get enough water in time. Make sure the hot and cold faucets are fully open, the hoses are not kinked, and your home has normal water pressure. Then turn off the faucets, remove the hoses at the washer and clean the small inlet screens. Mountain View's hard water can clog these screens with grit.

If water flows strongly from both hoses into a bucket but the washer still will not fill, the water inlet valve or pressure sensor is the next suspect. Old rubber hoses that bulge or crack should be replaced with braided ones while you are back there.

What should you do about door lock codes?

For F5E1 or F5E2, close the door or lid firmly and check that no clothing is caught in the latch. For F5E3 or dL, the washer cannot unlock: wait two minutes, make sure the tub has no water, then run Drain and Spin. Never force the door open while it is locked, because you can break the latch and the lock assembly.

If the washer is full of water and the door is still locked, turn the power off, drain it through the pump filter on front loaders, and wait a few minutes before trying again. A lock that fails over and over usually needs a new lock assembly, one of the more common repairs we make on Whirlpool front loaders.

When does a Whirlpool code mean a part has failed?

If the same code returns after you clean the filter, check the hoses and reset the power, a part has likely failed. Common repairs are drain pumps, inlet valves, door locks, pressure sensors and motor control boards. Any code with a burning smell, water on the floor or a washer that will not turn off should get a technician right away.

Washer repairs in Mountain View usually cost about $150 to $450 with parts and labor, and a diagnostic visit is about $95 to $150, often credited toward the repair. For drain pumps, locks and valves on a washer under 10 years old, repair usually makes sense. Our team for washer repair in Mountain View works on Whirlpool, Maytag, Kenmore and other brands.

How do you keep Whirlpool error codes from coming back?

Use only HE detergent and less than the cap line, clean the drain pump filter every one to three months on front loaders, leave the door open after washing, and do not overload the drum. Check the fill hoses once a year and keep the washer level. These steps prevent most drain, suds, lock and balance codes.

  • Empty pockets before washing. Coins and hair pins are the top cause of drain codes.
  • Run a monthly cleaning cycle with a washer cleaner tablet or bleach.
  • Wipe the door gasket and leave the door ajar to stop odor and mold.
  • Wash bulky items like comforters alone so the drum can balance.

We repair Whirlpool washers across Mountain View, ZIP codes 94040, 94041 and 94043, from apartments near Rengstorff Park and Shoreline to family homes in Cuesta Park, Monta Loma and Waverly Park.

Other common repairs we see in Mountain View

More quick answers from the kitchen: what to do when your oven is not preheating all the way, and why an electric oven is not working but the stove top is.

Frequently asked questions

How do I reset a Whirlpool washer error code?

Press Power or Cancel twice to clear the code, then start a Rinse and Spin cycle. If that does not work, unplug the washer or switch off its breaker for about one minute, then restore power. If the same code returns, the part it points to needs checking.

What does F9E1 mean on a Whirlpool washer?

F9E1 means the washer took too long to drain. The most common causes are a clogged drain pump filter on front loaders, a kinked drain hose or a clog in the standpipe. If the hose and filter are clear and the pump hums without draining, the pump may have failed.

What does F5E3 mean on a Whirlpool washer?

F5E3 means the door or lid will not unlock. Wait two minutes, make sure no water is in the tub, then try Drain and Spin. If the door still stays locked, the lock assembly or its wiring may have failed.

What does LF mean on a Whirlpool washer?

LF means Long Fill: the washer is not getting enough water fast enough. Check that both faucets behind the washer are fully open, the fill hoses are not kinked and the inlet screens are not clogged with sediment.

How much does washer repair cost in Mountain View?

Most washer repairs in Mountain View cost about $150 to $450 with parts and labor. The diagnostic visit is about $95 to $150 and is often credited toward the repair.

Is it worth repairing a Whirlpool washer that shows error codes?

Usually yes if the washer is under about 10 years old and the problem is a pump, lock, valve or sensor. If the code points to the motor control board or tub bearings on an older washer, compare the repair price with a new machine.

Live 24/7 · Mountain View, CA

Talk to an appliance technician now

Tell us what your appliance is doing. We will quote the visit on the phone and book the first open slot, often the same day.

  • Upfront price before any work
  • All major and luxury brands
  • Fridge and leak calls go first

More appliance repair guides

Need an appliance fixed today?

Call now to talk to a real person, any time of day or night.

(650) 459-7977 Call Now – (650) 459-7977

Our appliance repair services in Mountain View

One call covers every major appliance in your home. Pick a service for signs, costs, and how the repair works.

Call Now – (650) 459-7977