Samsung Washer Error Codes: What Each One Means and What to Do

Your Samsung washer stopped mid-cycle and the display is flashing a code. Most of these codes point to a simple problem you can check in a few minutes, like a kinked hose, a clogged filter or a lopsided load. Others point to a part that has failed. This guide decodes the common ones.

Call Now – (650) 459-7977
  • Open 24/7
  • Fast response
  • Upfront quotes
  • All major brands
Front-load washer in a Mountain View laundry room with the door open, wet towels left in the drum and a technician's tool bag and flashlight on the floor

How do you read a Samsung washer error code?

Samsung codes are short letter and number pairs, like 4C or dC. Newer washers end most codes in "C", while older ones show the same fault ending in "E". So 4C and 4E mean the same thing. Write down the exact code, note when in the cycle it appeared, and try a reset before you call for service.

Start with a simple reset. Turn the washer off, unplug it or flip its breaker for one minute, then run a short Rinse and Spin. If the code was a one-time glitch, it will not come back. If it does come back, use the table below to find the cause.

CodeOlder versionWhat it meansFirst check
4C4E, E1Not enough water coming inFaucets open, hoses not kinked, inlet screens clean
5C5E, SE, E2Water is not drainingClean the debris filter, check the drain hose
UEUB, UbLoad is unbalancedSpread clothes out, level the washer
dCdE, dL, dsDoor or lid not lockedClose the door firmly, check for clothes in the seal
LELC, LE1Water leak detectedLook under the washer and behind it for water
OEOF, OCToo much water (overflow)Too much detergent or a sticking inlet valve
HEHC, HE1Water heating problemUsually a heater or sensor, needs service
3C3E, EAMotor or motor sensor problemDo not overload; needs service if it repeats
tEtC, tE1Temperature sensor faultNeeds service
SdSud, 5dToo many sudsUse less HE detergent, run a rinse

Model lines differ a little, so check the code list in your owner's manual too. The model number is on a sticker inside the door frame or on the back of the washer.

What should you do about a 4C water supply code?

A 4C code means the washer filled too slowly or not at all. In most homes it is a closed or half-open faucet, a kinked fill hose, or clogged mesh screens where the hoses connect to the washer. If water pressure is fine and the screens are clean, the water inlet valve inside the washer may have failed.

  1. Make sure both the hot and cold faucets behind the washer are fully open.
  2. Pull the washer out a few inches and look for kinks in the fill hoses.
  3. Turn the faucets off, unscrew the hoses at the washer and check the small screens for grit or scale.
  4. Run a cold water fill and watch whether water flows in strongly.

Hoses older than about five years are worth replacing at the same time. Steel braided hoses last longer and burst less often than plain rubber ones.

What does a 5C drain code mean, and how do you fix it?

A 5C code means the washer could not pump water out in time. On Samsung front-loaders the most common cause is a clogged debris filter behind the small panel at the bottom front. Socks, coins, hair ties and lint collect there. Clean it first, then check the drain hose and the standpipe it drains into.

Put towels and a shallow pan down, open the small panel, and pull out the little drain tube to let the water out slowly. Then unscrew the filter and clean it. On top-loaders, check the drain hose behind the washer for a kink or a clog. If the filter and hose are clear and you hear a hum but no water moves, the drain pump has likely failed.

Code keeps coming back after you cleaned the filter? Call for a Samsung washer check in Mountain View today.

Call Now – (650) 459-7977

Why does a Samsung washer show UE and refuse to spin?

UE means the washer sensed the load bouncing off center, so it slowed the spin to protect the drum. A single heavy item, a twisted bedsheet or a washer that rocks on an uneven floor is the usual cause. If it happens with every normal load, worn shock absorbers, a suspension spring or a motor sensor may be the problem.

  • Pause the cycle, open the door and spread clothes out evenly.
  • Wash bulky items like rugs and comforters with one or two towels to balance them.
  • Check that all four feet touch the floor. Adjust the feet and tighten the lock nuts.
  • If the washer is on a stacked pedestal or upstairs floor, make sure it is not walking across the room during spin.

What do the door, leak and overflow codes mean?

dC means the door or lid did not lock. It is often clothing caught in the seal or a door not pushed fully closed, but a worn door lock or latch can cause it too. LE means a sensor found water in the base of the washer. OE means the tub filled too high, often from too much soap or a valve that sticks open.

If you see LE, turn the washer off and look for water under it before running another load. A leaking drain hose, a cracked filter cap or a torn door boot are common sources. For an OE code that repeats even with the correct amount of HE detergent, the inlet valve or water level sensor usually needs to be replaced.

Which codes need a technician?

Codes that point to parts inside the washer, like HE for heating, 3C for the motor, tE for the temperature sensor, or a 5C or dC that keeps returning after you have checked the filter and door, usually need a technician. These faults need a meter to test safely, and the parts are behind panels that are hard to reach.

When you call, have the model number, the code and when it showed up. That helps a technician bring the likely part on the first visit. Our team handles Samsung washer repair in Mountain View along with LG, Whirlpool, Maytag, GE, Bosch and Miele washers in ZIP codes 94040, 94041 and 94043.

Many Samsung codes match other brands' faults with different names. If you also have an LG, our LG washer error code guide decodes those. And if you are helping a family member far from the Bay Area, a local team handles appliance repair in New Braunfels, TX.

What does a Samsung washer repair cost in Mountain View?

Most Samsung washer repairs in Mountain View cost about $150 to $400 with parts and labor. Clearing a drain pump clog or replacing a door lock usually sits near the low end. A drain pump, inlet valve or suspension parts land in the middle. Control boards and motor parts are at the top. A diagnostic visit runs about $95 to $150.

Code and repairApprox. cost in Mountain View
Diagnostic visit$95 – $150
5C: pump clog cleared or drain pump replacedLow to middle of $150 – $400
4C or OE: water inlet valveWithin $150 – $400
dC: door lock assemblyLow to middle of $150 – $400
UE: shocks or suspensionWithin $150 – $400
3C, HE or control boardHigh end of $150 – $400

Washers in Mountain View homes from Old Mountain View to Monta Loma and Cuesta Park often sit in tight hall closets. That can make a leak or a walking washer more serious, so it is worth fixing a repeating code early.

Other appliance problems we fix in Mountain View

Kitchen trouble too? Here is what to check when a GE microwave vent fan won't turn off. In the laundry room, our guide explains why does my dryer turn off after a few minutes and what to clean first.

Frequently asked questions

How do I reset my Samsung washer error code?

Turn the washer off, unplug it or switch off its breaker for about one minute, then plug it back in and start a short Rinse and Spin cycle. This clears a code caused by a one-time glitch. If the same code comes back, the cause is still there and needs to be checked.

What does 4C mean on a Samsung washer?

4C, also shown as 4E or E1 on older models, means the washer is not getting enough water. Check that both faucets behind the washer are fully open, the hoses are not kinked and the small screens where the hoses connect are not clogged. A failed water inlet valve can also cause it.

What does 5C mean on a Samsung washer?

5C, also 5E, SE or E2, means the washer cannot drain. On front-loaders, clean the debris filter behind the small door at the bottom front. Then check the drain hose for kinks or a clog. If the filter and hose are clear, the drain pump may have failed.

Why does my Samsung washer say UE?

UE, also UB or Ub, means the load is out of balance, so the washer will not spin at full speed. Stop the washer, spread the clothes evenly or add a few similar items, and make sure the washer is level and not rocking. A single heavy item like a rug or comforter often triggers it.

Is it worth repairing a Samsung washer with an error code?

Usually, if the washer is under about 8 to 10 years old. Most washer repairs in Mountain View cost about $150 to $400 with parts and labor, plus a diagnostic visit of about $95 to $150. A control board or motor near the top of that range on an older washer may tip it toward replacement.

Live 24/7 · Mountain View, CA

Talk to an appliance technician now

Tell us what your appliance is doing. We will quote the visit on the phone and book the first open slot, often the same day.

  • Upfront price before any work
  • All major and luxury brands
  • Fridge and leak calls go first

More appliance repair guides

Need an appliance fixed today?

Call now to talk to a real person, any time of day or night.

(650) 459-7977 Call Now – (650) 459-7977

Our appliance repair services in Mountain View

One call covers every major appliance in your home. Pick a service for signs, costs, and how the repair works.

Call Now – (650) 459-7977