LG Washer Error Codes: What They Mean and How to Fix Them

Your LG washer stops mid-cycle and the display shows two letters, like OE or UE. That code is the washer telling you which system it is having trouble with: draining, filling, balance, the motor, the door or a sensor. Many codes clear with a simple check you can do in ten minutes. Others mean a pump, lock or motor needs testing. Here is what the common codes mean and what to do next.

Call Now – (650) 459-7977
  • Open 24/7
  • Fast response
  • Upfront quotes
  • All major brands
Technician pointing at the error code on a front-load washer display in a Mountain View laundry room

What do LG washer error codes mean?

An LG washer error code is a short message from the control board that names the system with a problem: drain, water supply, balance, motor, door lock, water level sensor or a leak. Front-load and top-load LG washers share most codes. The code tells you where to look first. It does not always tell you which single part has failed.

Write down the code and your model number before you reset anything. On most front loaders, the model label is inside the door frame. On top loaders, look under the lid or on the back panel. If a code keeps coming back, our washer repair Mountain View team can test the part it points to.

Which LG washer codes are most common?

The ten codes we see most often are OE (drain), IE (water inlet), UE or uE (unbalanced load), LE (motor locked), dE (door open), PE (water level sensor), FE (overfill), tE (heater or temperature sensor), SUD (too many suds) and AE (leak detected). Drain and balance codes are by far the most common in Mountain View homes.

CodeWhat it meansTry firstLikely repair
OEWater is not drainingClean the drain pump filter, check the drain hoseDrain pump
IEWater is not fillingOpen both taps fully, check hoses for kinksInlet valve or inlet screens
UE / uELoad is unbalancedSpread out the load, level the washerShocks, springs or hall sensor
LEMotor is locked or overloadedRemove some clothes, unplug for 10 minutesMotor stator, rotor or sensor
dE, dE1, dE2Door is open or not lockingClose the door firmly, clear the latchDoor lock or switch
PEWater level sensor problemPower resetPressure sensor or its hose
FEToo much water (overfill)Turn off the taps and unplugInlet valve stuck open or sensor
tEHeater or temperature sensor faultPower resetThermistor or heater
SUD / SudToo many sudsUse less HE detergent, run Rinse and SpinUsually no repair
AELeak detected inside the baseCheck hoses and the floorLeaking hose, pump or tub seal

Codes can differ a little from model to model, so your owner's manual has the final word.

How do you fix an OE drain code?

Most OE codes come from a clogged drain pump filter. On front loaders, open the small panel at the bottom front, lay towels down, drain the water from the small hose into a pan and unscrew the filter. Clear out lint, coins and hair ties, then put it back tightly. Also check that the drain hose is not kinked or pushed too far down the standpipe.

  1. Unplug the washer and put a shallow pan and towels in front of it.
  2. Open the access panel and drain the water from the small hose first.
  3. Turn the filter counterclockwise slowly and remove debris.
  4. Reinstall the filter firmly, so it does not leak.
  5. Run a Rinse and Spin cycle and watch for the code.

If the filter is clean and the washer hums but does not drain, the pump has likely failed. Our guides on a front-load washer drain pump filter and a washer not draining go step by step.

What should you do about UE and LE codes?

For UE, stop the washer, spread the clothes evenly and avoid washing one heavy item, like a bath mat or comforter, by itself. Check that the washer sits level and does not rock. For LE, take out part of the load, unplug for 10 minutes and try again. If either code returns with normal loads, a worn part is likely.

A washer that bangs or walks across the floor during spin often has worn shock absorbers or springs. See our guide to a washer shaking during spin for the checks. LE codes that return after a reset usually need a technician to test the motor stator, rotor magnets and the hall sensor, because the parts can look fine but read wrong on a meter.

Why does my LG washer show IE or a door code?

IE means water is not coming in fast enough. Make sure both supply taps are fully open, hoses are not kinked and the small screens where the hoses connect are not clogged with sediment. Door codes mean the lock did not engage: clear any clothing from the gasket, close the door firmly and reset. A lock that clicks but never latches needs replacing.

Older Mountain View homes, including many in Old Mountain View and Rex Manor, still have original supply valves that do not open fully. If yours are stiff or crusty, replace them before you replace an inlet valve. For more on fill problems, read our guide to a washer not filling with water. If the door will not open after a cycle, see washer door won't unlock.

When should you call a technician for an LG washer code?

Call when a code comes back after a reset and the basic checks, when you see LE, PE, tE, FE or AE, when water is on the floor, or when you smell burning. These usually mean a part has failed. A technician tests the pump, lock, sensor or motor with a meter instead of guessing and replacing parts one at a time.

A visit starts with the diagnostic, approx. $95 to $150, which is often credited toward the repair. Most LG washer repairs in Mountain View fall in the approx. $150 to $450 range with parts and labor.

RepairWhere it falls (approx.)
Diagnostic visit$95 – $150, often credited to the repair
Inlet valve, door lock, pressure sensorLow to middle of $150 – $450
Drain pump, shocks and springsMiddle of $150 – $450
Motor stator, control boardHigh end of $150 – $450

If an older washer needs a board plus a motor part, compare the cost with a new machine. Our repair or replace guide helps with that choice.

How do you prevent LG washer error codes?

Clean the drain pump filter every two to three months, use only HE detergent in the right amount, and leave the door open after washing so the gasket dries. Keep the washer level, avoid overloading and check the supply hoses once a year. These habits prevent most drain, suds, balance and leak codes.

  • Empty pockets before washing. Coins and hair ties cause many OE codes.
  • Run the Tub Clean cycle monthly to limit buildup and odor.
  • Replace rubber supply hoses with braided hoses about every five years.
  • Wash heavy single items with a few towels to keep the drum balanced.

We repair LG washers across Mountain View, ZIP codes 94040, 94041 and 94043, from Cuesta Park and Waverly Park to the townhomes near Whisman Station and Shoreline.

Other common repairs we see in Mountain View

More quick answers: what to do when your microwave is not heating up but runs, why an electric oven is not working but the stove top is, and why your dryer turns off after a few minutes.

Frequently asked questions

How do I reset an LG washer error code?

Turn the washer off, unplug it for about 5 to 10 minutes, then plug it back in and run a Rinse and Spin cycle. If the same code returns right away, the reset did not fix the cause and the part the code points to needs checking.

What does OE mean on an LG washer?

OE is a drain error. The washer could not pump water out in time. The usual causes are a clogged drain pump filter, a kinked or clogged drain hose, or a failed drain pump.

What does UE mean on an LG washer?

UE means the load is unbalanced, so the washer will not spin at full speed. Redistribute the clothes, avoid washing one heavy item alone and make sure the washer is level. If UE shows with balanced loads, the shocks, springs or a sensor may be worn.

What does LE mean on an LG washer?

LE is a motor locked error. Something is stopping the drum from turning, such as an overload or an item stuck between the drum and tub, or the motor, rotor or sensor has a fault. Unplug for 10 minutes and try a small load. If it returns, call for repair.

How much does LG washer repair cost in Mountain View?

Most washer repairs in Mountain View cost approx. $150 to $450 with parts and labor. The diagnostic visit is approx. $95 to $150 and is often credited toward the repair.

Live 24/7 · Mountain View, CA

Talk to an appliance technician now

Tell us what your appliance is doing. We will quote the visit on the phone and book the first open slot, often the same day.

  • Upfront price before any work
  • All major and luxury brands
  • Fridge and leak calls go first

More appliance repair guides

Need an appliance fixed today?

Call now to talk to a real person, any time of day or night.

(650) 459-7977 Call Now – (650) 459-7977

Our appliance repair services in Mountain View

One call covers every major appliance in your home. Pick a service for signs, costs, and how the repair works.

Call Now – (650) 459-7977