Dishwasher Hums but Won't Drain and There Is No Clog: 6 Parts to Check

You already did the usual fixes. The filter is clean, the drain hose is not kinked and the sink drains fine. But at the end of the cycle, the dishwasher hums, and the water just sits there. When there is no clog you can see, the problem is usually a part: the drain pump, something jammed in it, or a valve that will not open. Here is how to narrow it down.

Call Now – (650) 459-7977
  • Open 24/7
  • Fast response
  • Upfront quotes
  • All major brands
Checklist graphic of six parts to check when a dishwasher hums but will not drain and there is no clog

Why does a dishwasher hum but not drain when there is no clog?

When the filter and hose are clear, a humming dishwasher that will not drain usually has a drain pump problem. Either something small is jammed in the pump impeller, the pump motor is worn out, or the check valve that stops dirty water flowing back is stuck shut. Less often, the air gap, the disposal connection or the control board is to blame.

If the checks below do not fix it, our dishwasher repair Mountain View technicians can test the pump, clear the sump and replace failed parts, usually in one visit.

If you have not checked the filter and drain hose yet, start with our main guide to a dishwasher not draining, which covers clogs step by step.

What does the hum tell you?

The sound is a clue. A steady hum with no water moving means the pump motor is getting power but cannot turn. A grinding or rattling sound means something is in the impeller. Silence with water sitting in the tub means the pump may not be getting power at all, which points to wiring or the control board.

What you hear or seeMost likely cause
Steady hum, no drainingJammed impeller or seized pump motor
Rattle or grinding during drainGlass, a pit or a bone in the pump
Drains slowly, water left after cycleCheck valve sticking or partial air gap blockage
Silent, no hum, water in tubPump not getting power: wiring or control board
Drains only after running the disposalBlockage at the disposal inlet or air gap
Error code for drain on the displayPump, hose or sensor; check the code in your manual

What can you safely check yourself?

Turn off the dishwasher's power first at the breaker or by unplugging it. Then bail out the standing water with a cup and towels, take out the filter, and look and feel into the sump below it. Many jammed pumps are freed by removing one small piece of glass or plastic from that opening.

  1. Turn off power at the breaker. Do not rely on the door switch.
  2. Bail out the water and lift out the filter assembly.
  3. With gloves on, feel inside the sump for glass, bones, pits, labels or twist ties.
  4. Some models have a small pump cover in the sump. If yours does, remove it and check that the impeller turns freely.
  5. Clean the air gap cap on the sink, if you have one. Pull it off and clear any gunk.
  6. If the drain hose goes to a disposal, make sure the knockout plug was removed when the disposal was installed.
  7. Put everything back, restore power and run a short rinse or drain cycle.

Still humming with water in the tub? Call now for same-day dishwasher repair in Mountain View.

Call Now – (650) 459-7977

Which parts usually fail?

Six parts cause most drain failures when there is no clog in the hose: the drain pump impeller, the drain pump motor, the check valve, the air gap, the disposal connection and the control board or its wiring. A technician tests them in order, from the most common and cheapest to the least common.

1. A jammed impeller

The impeller is a small plastic fan inside the drain pump. Broken glass, fruit pits and bits of bone get past the filter and wedge it in place. The motor hums but cannot spin. Clearing it often fixes the problem without new parts. Sometimes the impeller blades break and the pump needs replacing.

2. A worn drain pump motor

Pump motors wear out after years of use, especially in dishwashers that run once or twice a day. A weak motor may start, hum loudly and then stop. A meter test shows whether it is getting power and whether the motor winding is good.

3. A stuck check valve

The check valve is a small flap that lets water out but stops dirty sink water from flowing back in. Grease and food can glue it shut, or it can crack. Water drains slowly, or not at all, even with a good pump.

4. A blocked air gap

The air gap is the small chrome cap on the sink next to the faucet. It keeps sink water from siphoning into the dishwasher. Food builds up inside it. If water spurts from the air gap during the drain, it is blocked.

5. The garbage disposal connection

If the drain hose connects to a disposal, a clogged disposal inlet blocks the dishwasher too. A brand-new disposal with the knockout plug still in place stops all drainage right away.

6. The control board or wiring

If the pump is silent and gets no power during the drain step, the board or a wire is at fault. This needs meter testing. Control boards cost more, so it is worth confirming before you buy one.

Is standing water in the dishwasher a problem?

A little water in the sump, under a cup, is normal on many models. More than an inch, or water over the filter, is not. Standing water starts to smell within a day or two, and if the pump keeps trying to run against a jam, the motor can overheat and fail. Do not keep running cycles to force it.

A bad smell is often the first sign something is off. Our guide to a dishwasher that smells bad covers cleaning once it is draining again.

How much does it cost to fix a dishwasher that won't drain?

Most dishwasher repairs in Mountain View cost about $150 to $400 with parts and labor. Clearing a jammed impeller, replacing a drain pump, a check valve or a drain hose all usually fall in that range. The technician confirms the cause and gives you the price before any work starts.

ApplianceTypical repair (approx.)
Dishwasher$150 – $400

Dishwashers usually last about 9 to 12 years. If yours is younger and the tub is not leaking or rusting, repairing a drain part is almost always worth it. If it is older and has other problems, our guide on whether to repair or replace an appliance can help.

Why do we see this so often in Mountain View kitchens?

Many Mountain View homes run the dishwasher daily, and plenty of kitchens in Old Mountain View, Monta Loma and the Whisman area have older disposals and air gaps that collect food. Newer apartments near North Bayshore and the Castro Street area often have compact dishwashers with small sumps that jam more easily.

Scraping plates before loading, cleaning the filter every month and running the disposal before you start the dishwasher all help keep the drain path open. We serve every Mountain View ZIP code: 94040, 94041 and 94043.

How do you keep the drain pump from jamming again?

Scrape food into the trash, not the dishwasher, and check the filter every few weeks. Load glasses so they cannot tip and break, and keep small items like lids and twist ties in a basket. Run the disposal before starting the dishwasher, and clean the air gap cap a few times a year.

  • Clean the filter monthly, or weekly if you do not rinse dishes.
  • Remove labels from jars before washing them.
  • Use a small-items basket for lids and baby bottle parts.
  • If a glass breaks inside, clear every piece from the sump before the next run.

Other common repairs we see in Mountain View

More kitchen and laundry help: a dryer turns off after a few minutes, a dishwasher that leaves dishes wet and why is my oven not turning on. For anything else, see our appliance repair in Mountain View services.

Frequently asked questions

Why is my dishwasher humming but not draining?

A hum with no draining usually means the drain pump is getting power but cannot spin. The most common cause is a piece of glass, a bone or a cherry pit jammed in the pump impeller. A worn pump motor or a stuck check valve can do the same thing.

Can I fix a dishwasher drain pump myself?

You can safely remove the filter and look into the sump for debris after turning off power. Replacing the pump means pulling the dishwasher out or opening the base, working near water and wiring. Most people have a technician do it.

How much does it cost to replace a dishwasher drain pump in Mountain View?

Most dishwasher repairs in Mountain View, including a drain pump replacement, cost about $150 to $400 with parts and labor. The technician confirms the cause and gives you the price first.

Is it worth fixing a dishwasher that won't drain?

Usually yes. Drain pumps, check valves and drain hoses are some of the most affordable dishwasher repairs. If the dishwasher is under about 10 years old and the tub is not leaking, a repair is almost always cheaper than replacing it.

Why does my dishwasher drain after I run the garbage disposal?

That points to a partial blockage where the drain hose meets the disposal or air gap. Running the disposal clears it for a while. Clean the air gap and the disposal inlet, and have the hose checked if it keeps happening.

Live 24/7 · Mountain View, CA

Talk to an appliance technician now

Tell us what your appliance is doing. We will quote the visit on the phone and book the first open slot, often the same day.

  • Upfront price before any work
  • All major and luxury brands
  • Fridge and leak calls go first

More appliance repair guides

Need an appliance fixed today?

Call now to talk to a real person, any time of day or night.

(650) 459-7977 Call Now – (650) 459-7977

Our appliance repair services in Mountain View

One call covers every major appliance in your home. Pick a service for signs, costs, and how the repair works.

Call Now – (650) 459-7977