Bosch Dishwasher Error Codes: What E15, E24, E25 and Other Codes Mean

Bosch dishwashers are everywhere in Mountain View kitchens, from remodeled Eichlers to new condos near the San Antonio center. They are quiet and reliable, but when something goes wrong they flash a code and stop. The good news: the most common codes point to water problems you can often clear in 20 minutes.

Call Now – (650) 459-7977
  • Open 24/7
  • Fast response
  • Upfront quotes
  • All major brands
Chart graphic of common Bosch dishwasher error codes and what each one means

What do Bosch dishwasher error codes mean?

Bosch codes start with E and a number. Most of the common ones are about water: E15 is water in the base, E24 and E25 are drain problems, and E22 is a clogged filter. Heating, pump and sensor faults use other numbers. Codes can differ a little by series and year, so check the manual for your model as well.

If a code keeps coming back after the steps below, our dishwasher repair in Mountain View technicians test pumps, valves, heaters and boards on Bosch 100, 300, 500, 800 and Benchmark models.

Which Bosch codes are most common?

Eight codes cover most of the calls we get on Bosch dishwashers. The table lists what each one usually means and whether you can try a fix yourself. Start with the drain and filter codes, because they are common and safe to check. Leave heater, motor and board codes to a technician.

CodeWhat it usually meansCan you try a fix?
E15Water in the base pan, leak protection trippedYes, dry the base and look for the leak
E24Slow drain: filter, hose or disposal inletYes, clean the filter and check the hose
E25Drain pump blocked or not runningYes, clear the pump cover under the filter
E22Filter cloggedYes, clean the filter
E21Wash pump motor not running rightNo, call for repair
E09 / E01Heating fault on many modelsNo, call for repair
E17 / E18Too much or too little water coming inCheck the water valve, then call
E27Power supply problem, such as low voltageCheck the outlet and breaker

How do you fix E15 (water in the base)?

E15 means water reached the tray under the tub and lifted a float. First find out where the water came from. Too much soap or the wrong soap is a common cause, and so is a small leak at a door seal, a spray arm or a hose. Dry the base, fix the leak, and the code clears.

  1. Turn off the breaker and the water valve under the sink.
  2. Remove the kick plate at the bottom front of the dishwasher.
  3. Soak up the water in the base pan with towels, or tilt the unit back carefully if it is not secured.
  4. Look for the source: suds, a wet hose clamp, a drip at the door seal or a crack.
  5. Restore power and run a short rinse cycle while you watch for drips.

Only use dishwasher detergent. Hand soap or a squirt of dish liquid can make enough foam to trip E15 in one cycle.

How do you fix E24 and E25 (drain codes)?

For both codes, start with the filter in the bottom of the tub. Twist it out, rinse it and wipe out the sump. For E24, then check the drain hose under the sink for kinks and the disposal connection for a clog. For E25, remove the small pump cover under the filter and clear glass, pits or labels.

  1. Cancel the cycle and turn off the breaker.
  2. Bail out standing water with a cup and a towel.
  3. Twist out the filter, rinse it under hot water and scrub it gently.
  4. For E25: lift out the white pump cover with a spoon handle and clear anything stuck around the impeller.
  5. Check the drain hose for kinks. If you just got a new disposal, make sure its knockout plug was removed.
  6. Run the garbage disposal, then restart a rinse cycle.

If the impeller does not turn freely, or you hear the pump hum with no water moving, the drain pump has likely failed and needs a new one.

Code keeps coming back? Call now for Bosch dishwasher repair in Mountain View.

Call Now – (650) 459-7977

When should you call a technician?

Call when a code returns after you cleared the filter and the drain path, when you see heater or motor codes, or when water is on the floor. Heater, motor and board faults need meter testing and parts that are not safe to guess at. A leak that reaches the floor can damage subfloor and cabinets fast.

  • E15 returns within a cycle or two after the base is dry
  • E24 or E25 returns with a clean filter and a clear pump
  • E09, E01 or E21 appear, or dishes come out cold and wet
  • The breaker trips when the dishwasher starts
  • You smell burning or see scorch marks near the kick plate

How much does Bosch dishwasher repair cost?

Most dishwasher repairs in Mountain View cost about $150 to $400 with parts and labor. Drain pumps, inlet valves, door seals and float switches usually fall inside that range. Heater and control board repairs can sit at the top. The diagnostic visit is usually about $95 to $150, and you get the price before any work starts.

ApplianceTypical repair (approx.)
Dishwasher$150 – $400

Bosch dishwashers often last 10 to 12 years. If yours is newer than that, a repair in this range is almost always better value than a new unit and a new install. Mountain View mixes soft Hetch Hetchy water with harder local supplies, so scale can still build on filters and spray arms, so a yearly filter clean and a rinse aid helps keep codes away. Our guide to hard water and your dishwasher explains more.

Other common repairs we see in Mountain View

Something else acting up? These guides may help: why is my oven not turning on, dryer keeps shutting off after a few minutes and a dishwasher that will not drain.

Frequently asked questions

What does E15 mean on a Bosch dishwasher?

E15 means the leak protection system found water in the base pan under the tub. A float switch trips and the drain pump runs to protect your floor. The water can come from a small leak, too much suds, or a cracked hose or seal.

How do I reset a Bosch dishwasher error code?

Press and hold Start or Start/Reset for about 3 seconds to cancel the cycle and let it drain. If the code returns, turn off the breaker for 2 to 3 minutes. A reset clears the code but not the cause, so check the filter, drain hose and base first.

What does E24 mean on a Bosch dishwasher?

E24 means the dishwasher is not draining well. The usual causes are a clogged filter, a kinked drain hose, a blocked garbage disposal inlet or a new disposal with the knockout plug still in place.

What is the difference between E24 and E25?

E24 points to a slow drain path, such as the filter, hose or disposal connection. E25 points to the drain pump itself, often a piece of glass, a pit or a label stuck under the pump cover, or a pump that has failed.

How much does Bosch dishwasher repair cost in Mountain View?

Most dishwasher repairs in Mountain View cost about $150 to $400 with parts and labor. A drain pump, inlet valve or leak repair usually falls inside that range. The diagnostic visit is about $95 to $150.

Live 24/7 · Mountain View, CA

Talk to an appliance technician now

Tell us what your appliance is doing. We will quote the visit on the phone and book the first open slot, often the same day.

  • Upfront price before any work
  • All major and luxury brands
  • Fridge and leak calls go first

More appliance repair guides

Need an appliance fixed today?

Call now to talk to a real person, any time of day or night.

(650) 459-7977 Call Now – (650) 459-7977

Our appliance repair services in Mountain View

One call covers every major appliance in your home. Pick a service for signs, costs, and how the repair works.

Call Now – (650) 459-7977